Reference Guide: Points
The key to generating the most complete, robust performance reports is properly mapping equipment points that in turn run the rules that feed the reports. Mapping the following key points into Resolute Synergyâ„¢ will automatically provide you with a large set of analytic rules, reports, and computed points.
Equipment Type |
Point |
AHU (Air Handling Units, Rooftop Units, Packaged Units) |
Building Static Pressure |
|
Cooling Command |
|
Damper Position |
|
Discharge Air Fan Command (single or common) |
|
Discharge Air Fan Frequency (single or common) |
|
Discharge Air Fan Speed (single or common) |
|
Discharge Air Fan Status (single or common) |
|
Discharge Air Flow |
|
Discharge Air Humidity |
|
Discharge Air Pressure |
|
Discharge Air Pressure Setpoint |
|
Discharge Air Temperature |
|
Discharge Air Temperature Setpoint |
|
Economizer Mode |
|
Effective Cooling Setpoint |
|
Effective Heating Setpoint |
|
Exhaust Air Flow |
|
Heating Command |
|
Mixed Air Temp |
|
Occupied Cooling Setpoint |
|
Occupied Heating Setpoint |
|
Occupied Mode |
|
Outside Air Damper Command (open/closed) |
|
Outside Air Damper Minimum Position Setpoint |
|
Outside Air Damper Position |
|
Outside Air Flow |
|
Outside Air Flow Minimum Setpoint |
|
Outside Air Humidity |
|
Outside Air Temperature |
|
Return Air Flow |
|
Return Air Humidity |
|
Return Air Pressure |
|
Return Air Temperature |
|
Unoccupied Cooling Setpoint |
|
Unoccupied Heating Setpoint |
|
Zone Humidity |
|
Zone Pressure |
|
Zone Temperature |
|
Zone Temperature Setpoint |
Boiler
Equipment Type |
Point |
Boiler |
Boiler Command |
|
Boiler Leaving Setpoint |
|
Boiler Status |
|
Entering Water Temperature |
|
Heating Command |
|
Leaving Water Temperature |
Chilled Water
Equipment Type |
Point |
Chilled Water |
Chilled Water Entering Temperature |
|
Chilled Water Leaving Temperature |
|
Chilled Water Setpoint |
|
Chiller Command |
|
Chiller Status |
|
Condenser Water Entering Temperature |
|
Condenser Water Leaving Temperature |
Cooling Tower
Equipment Type |
Point |
Cooling Tower |
Condenser Water Circ Pump Status |
|
Condenser Water Entering Temperature |
|
Condenser Water Leaving Temperature |
|
Condenser Water Leaving Temperature Setpoint |
|
Enable Command |
|
Fan Speed Signal |
|
Fan Status |
|
Sump Temperature |
FCU (Fan Coil Units)
Equipment Type |
Point |
FCU (Fan Coil Units) |
Cooling Command |
|
Effective Cooling Setpoint |
|
Effective Heating Setpoint |
|
Heating Command |
|
Occupied Cooling Setpoint |
|
Occupied Heating Setpoint |
|
Occupied Mode |
|
Unoccupied Cooling Setpoint |
|
Unoccupied Heating Setpoint |
|
Zone Temperature |
|
Zone Temperature Setpoint |
Heat Pump
Equipment Type |
Point |
Heat Pump |
Effective Cooling Setpoint |
|
Effective Heating Setpoint |
|
Occupied Cooling Setpoint |
|
Occupied Heating Setpoint |
|
Occupied Mode |
|
Unoccupied Cooling Setpoint |
|
Unoccupied Heating Setpoint |
|
Zone Temperature |
|
Zone Temperature Setpoint |
Meters
Equipment Type |
Point |
Meters |
Domestic Water Volume Total (accumulated) |
|
Energy Total (accumulated) |
|
Gas Volume Total (accumulated) |
VAV
(Variable Air Volume Boxes, Fan-Powered Boxes)
Equipment Type |
Point |
VAV (Variable Air Volume Boxes, Fan-Powered Boxes) |
Cooling Command |
|
Damper Command |
|
Damper Position |
|
Discharge Air Fan Status (single or common) |
|
Discharge Air Flow |
|
Discharge Air Flow Setpoint |
|
Discharge Air Temperature |
|
Effective Cooling Setpoint |
|
Effective Heating Setpoint |
|
Heating Command |
|
Occupied Cooling Setpoint |
|
Occupied Heating Setpoint |
|
Occupied Mode |
|
Reheat Command |
|
Return Air Flow |
|
Unoccupied Cooling Setpoint |
|
Unoccupied Heating Setpoint |
|
Zone Air Change Rate Outside Air |
|
Zone Air Change Rate Total Zone Pressure |
|
Zone Humidity |
|
Zone Pressure |
|
Zone Temperature |
|
Zone Temperature Deviation |
|
Zone Temperature Setpoint |